This article contains the probable reasons for the status of a virtual server being marked as DOWN on Citrix ADC.

Status of ADC Virtual Servers

The virtual servers on an ADC appliance can have any of the following state:

• UP
• DOWN
• OUT OF SERVICE

When the status of the virtual server is marked as UP, it is operational and ready to service requests.

You can use the URL Redirection feature of the ADC appliance or configure backup virtual servers to provide continuous service if the status of the main virtual server is marked as DOWN, unexpectedly.

The status of a virtual server might be marked as OUT OF SERVICE when you disable the virtual server but do not delete it.

View Status of ADC Virtual Servers

To view the status of a virtual server navigate to Traffic Management > Load Balancing > Virtual Servers. Alternatively, you can run the following command from the command line interface of the appliance to view the status of the virtual servers:
show vserver

Probable Reasons for the Status of Citrix ADC Virtual Server Being Marked as DOWN

No service is bound to the virtual server

A service provides the connections between the ADC appliance and the back end servers. Each virtual server must have atleast one service bound to it. Each service has a name and specifies an IP address, a port, and the type of data that is served.

To verify if services are bound to a specific virtual server, run the following command from the command line interface of the appliance:
> show vserver <VServer_Name>
If there are no services listed at the end of the output, then the reason for the status being marked as DOWN is because no service is bound to the virtual server.

For information on types of services and how create a service refer to Citrix Documentation .

All services bound to the virtual server are not available

To verify the status of the services bound to a specific virtual server, run the following command from the command line interface of the appliance:
> show vserver <VServer_Name>

The following is a sample output of show vserver command, when all services being not available is the reason for the status of a virtual server being marked as DOWN:

> show vserver example_down_vip
        example_down_vip (0.0.0.0:0) - HTTP     Type: ADDRESS
        State: DOWN
        Effective State: DOWN  ARP:DISABLED
        ...
1) Blue (10.198.4.43: 80) - HTTP State: DOWN     Weight: 1
Done

In this scenario, the status of the virtual server is marked as DOWN because the only bound service is not available. A virtual server must have at least one service bound and should be available, to ensure that the status of the virtual server is marked as UP.

A service might not be available because of multiple reasons, such as communication failure between the ADC appliance and the server hosting the service. You can use the following options to troubleshoot a service that is not available:

Run the following command to verify if any non-default server monitor is bound to the service:
> show service <Service_Name>

The following is a sample output for your reference:

> show service Blue
        Blue (10.198.4.43:80) – HTTP
        State: DOWN
        Last state change was at Mon Sep 15 14:46:29 2008 (+845 ms)
        Time since last state change: 1 days, 05:00:01.790
        Server Name: 10.198.4.43
        Server ID : 0   Monitor Threshold : 0
        ...
1)      Monitor Name: tcp-default
                State: DOWN     Weight: 1
                Probes: 10371   Failed [Total: 10371 Current: 10371]
                Last response: Failure - TCP syn sent, reset received.
                Response Time: N/A
 Done

In this scenario the service is not available because the monitor tcp-default fails indicating that the service is not accepting TCP connections. Consider the following points when troubleshooting such issues:

• The status of a service is marked as UP only if probes from all monitors bound to the service are successful.

If only default monitors are bound to the service and the service is not available, then verify the network connectivity between the ADC appliance and the back end servers.

If a virtual server hosts a Secure Socket Layer (SSL) service, then the status of the virtual server is marked as DOWN if an SSL cerkey is not bound to the virtual server. To resolve this issue, run the following command to bind an SSL certkey to the virtual server:
> bind ssl certkey <VServer_Name> <Certkey_Name>

The ADC Features are not enabled

You can configure ADC feature (load balancing, content switching and so on) entities such as services and virtual servers when a feature is disabled, but they will not function until you enable the feature. For information on enabling a feature of Citrix ADC refer to Citrix Documentation - Enabling or Disabling a Feature.

The ADC Features are not licensed

Before using a feature, make sure that your license supports the feature.For license overview click here .