Knowledge Center Home
> All Products
> NetScaler Application Delivery
> NetScaler Application Delivery Software 7.0
> NetScaler Application Delivery Software 7.0: Networking

NetScaler Application Delivery Software 7.0: Networking

Technotes	Created	Modified	Read	Rating
Access to the Web Servers is not Available through the NetScaler Appliance Symptoms You are not able to access the Web servers through the NetScaler appliance virtual servers (vservers) even though the vservers and services are running in the UP state. The vservers ... CTX116878	4/17/08	8/8/08	463	Unrated
How to Set up Link Aggregation and VLAN Trunking on a NetScaler Summary This document shows the basic configuration needed to set up an 802.3ad link aggregate between a NetScaler and a switch that supports Link Aggregation Control Protocol (LACP). On top ... CTX117113	6/25/08	6/25/08	384
How to Restrict Access Gateway Enterprise Edition from Displaying Your Listening Ports Summary This article describes how to restrict Citrix Access Gateway Enterprise Edition from displaying your listening ports. Background When you perform a scan for ports with Access Gateway ... CTX117107	5/30/08	5/30/08	299
Configuring an LDAP Monitor Summary This article describes how to configure the NetScaler Lightweight Directory Access Protocol (LDAP) User monitor. It is recommended that the basic Active Directory (AD) authentication... CTX111109	5/28/08	5/28/08	247	Unrated
IP Address Conflict in the Network Symptoms When migrating from the F5 appliance to the NetScaler appliance, the virtual servers are running. However, you cannot connect to the virtual servers using telnet or other similar uti... CTX116879	5/9/08	5/9/08	250	Unrated
How to Change the HTTP 1.1 Response to the HTTP 1.0 Response on a NetScaler Appliance Summary This article describes how to change the HTTP 1.1 Response to the HTTP 1.0 Response on a NetScaler appliance. In a network, you can connect a NetScaler appliance to the multiple serve... CTX116784	5/9/08	5/9/08	234	Unrated
How to Configure Outbound Link Load Balancing for Two ISP Links on a NetScaler Appliance with Reverse Network Address Translation Summary This article describes how to configure Outbound Link Load Balancing for Two ISP Links on a NetScaler Appliance with Reverse Network Address Translation (RNAT) You apply the Link Load... CTX116995	5/8/08	5/8/08	406
How to Delete the Last Mapped IP from the Configuration Summary This document describes the procedure to delete the last mapped IP (MIP) from the NetScaler configuration file. Background Under normal circumstances, you cannot remove the last mappe... CTX116972	4/21/08	4/21/08	469	Unrated
How to Configure the Border Gateway Protocol on a NetScaler Simple bgp configuration on the NetScaler. CTX116760	4/8/08	4/8/08	278	Unrated
How to Change the NetScaler Default IP Address Instructions for changing the default NSIP NS uses when ns.conf is missing. CTX116761	3/31/08	3/31/08	311	Unrated
FAQ: What is the trunk option on a Netscaler interface used for? Q: What is the trunk option on a NetScaler interface used for? A: Different network equipment vendors use the term trunk differently. Some use it to describe a switch port capable of carryi... CTX115575	1/21/08	1/21/08	613
How to Configure a NetScaler to Authenticate Against the Global Catalog Server Summary In a multi-domain forest the Active Directory (AD) database becomes partitioned such that each domain maintains a list of only those objects that belong in that domain. For example, a... CTX113655	1/4/08	1/7/08	519	Unrated
How to Configure Link Redundancy Using a Failover Interface Set Configuring the Netscaler to for link redundancy to overcome the switch being a single point of failure. CTX114657	1/4/08	1/4/08	1,115	Unrated
NetScaler 9400 Series Units on Release 7.0 Build 56 and Deployed in a High Availability Pair Report a MAC Address Conflict Symptoms NetScaler 9400 series units running on release 7.0 build 56 and deployed in a High Availability (HA) pair report a Media Access Control (MAC) address conflict. Note : The primary and... CTX115002	12/14/07	12/14/07	343	Unrated
Why Are You Unable to Configure 64-bit Simple Network Management Protocol Counters Using IF-MIB on NetScaler Release 7.0? Q: Why are you unable to configure 64-bit Simple Network Management Protocol (SNMP) counters using IF-MIB on NetScaler release 7.0? A: The IF-MIB is supported only in release 8.0 and later. ... CTX114996	12/13/07	12/13/07	437	Unrated
Spanning Tree Protocol and NetScaler Summary This document discusses Spanning Tree Protocol (STP) and the NetScaler. Information STP is used to avoid looping in the network by following a mathematical algorithm developed by Radia Per... CTX112341	2/13/07	11/30/07	4,520
Active Directory Group Extraction for LDAP Summary This document discusses how to configure the NetScaler to allow access to the NetScaler VPN based on Active Directory groups through Lightweight Directory Access Protocol (LDAP) authentica... CTX111079	6/25/07	6/25/07	8,370	Unrated
How to Remove a BGP Configuration Summary This document describes how to clear or remove a Border Gateway Protocol (BGP) configuration. Requirements The following items are necessary to perform this task: • Administrative/shell/ro... CTX111571	6/20/07	6/21/07	2,301	Unrated
How to Load Balance Web Interface with a NetScaler Summary This article describes how to load balance Web Interface with a NetScaler. Background When a NetScaler is used to load balance Web Interface, it uses either the Management IP (MIP) address... CTX111080	1/31/07	4/6/07	8,180
What is the -tagged parameter used for? Q: What is the –tagged parameter used for? A: The –tagged parameter is used when binding a virtual LAN (VLAN) ID to a physical interface (or LA channel), to put that interface in that VLAN. Fram... CTX110541	10/25/06	10/25/06	3,957	Unrated
What is the -trunk Parameter Used For? Q: What is the –trunk parameter used for? A: The –trunk ( ON \| OFF ) parameter can be set on an interface (or Link Aggregation channel) to put the interface in “trunk mode.” For example: > se... CTX110540	10/23/06	10/23/06	3,502	Unrated
Understanding Metric Exchange Protocol and Monitors for Global Server Load Balancing Summary This document provides an overview of Global Server Load Balancing (GSLB), Metric Exchange Protocol (MEP), monitors, and their relationship in the load balancing decision. Prerequisites ... CTX111081	10/10/06	10/12/06	5,504
The NetScaler 12000 System does not Pass Traffic on Interface 0/1 Symptoms When connecting the NetScaler 12000 system to a switch through the 0/1 interface located on the back of the system, it may not pass traffic even though the NetScaler has been configured w... CTX111108	10/10/06	10/10/06	3,266	Unrated
HTTP-ECV Monitor Probes Are Failing Symptoms A custom monitor of type HTTP-ECV has been defined, but is failing probes even though the configured page can be accessed on the Web server. Cause A custom monitor of type HTTP-ECV may be... CTX110167	8/30/06	8/30/06	5,211
Behavior of Address Resolution Protocol (ARP) and Gratuitous ARP on the NetScaler Summary This document describes the behavior of the Address Resolution Protocol (ARP) and Gratuitous ARP (GARP) on NetScaler devices. Background Typical network devices use ARP to locate the hardw... CTX109980	7/27/06	7/27/06	847
Understanding Client Keep-Alives Summary HTTP operates on what is called a request-response model. This means that a client generates a request for information and passes it to the server, which answers it. In the original implem... CTX108955	3/29/06	4/3/06	12,133

Knowledge Center

Products

Presentation Server

Presentation Server Clients (ICA)

XenServer

XenDesktop

XenDesktop 2.0

NetScaler Application Delivery

Access Gateway

EdgeSight

Provisioning Server

WANScaler

Password Manager

>> View All Products

Knowledge Resources